View 74ALVC16245DGG_2836292.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the 74alvc16245; 74alvch16245 is a 16-bit transceiver featuring non-inverting 3-state bus compatible outputs in both send and receive directions. the 74alvc16245; 74alvch16245 features two output enable inputs (pins n oe) for easy cascading and two send or receive inputs (pins ndir) for direction control. pins n oe control the outputs so that the buses are effectively isolated. this device can be used as two 8-bit transceivers or one 16-bit transceiver. the 74alvch16245 has an active bushold circuitry which is provided to hold unused or ?oating data inputs at a valid logic level. this feature eliminates the need for external pull-up or pull-down resistors. 2. features n wide supply voltage range from 1.2 v to 3.6 v n complies with jedec standard jesd8-b n cmos low power consumption n multibyte ?ow-through standard pin-out architecture n low inductance multiple v cc and gnd pins for minimize noise and ground bounce n direct interface with ttl levels n all data inputs have bushold (74alvch16245 only) n output drive capability 50 w transmission lines at 85 c n current drive 24 ma at v cc = 3.0 v. 74alvc16245; 74alvch16245 16-bit transceiver with direction pin; 3-state rev. 03 12 may 2004 product data sheet
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 2 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 3. quick reference data [1] c pd is used to determine the dynamic power dissipation (p d in m w). p d = c pd v cc 2 f i n+ ? (c l v cc 2 f o ) where: f i = input frequency in mhz; f o = output frequency in mhz; c l = output load capacitance in pf; v cc = supply voltage in volts; n = total load switching outputs; ? (c l v cc 2 f o ) = sum of outputs. [2] the condition is v i = gnd to v cc . 4. ordering information table 1: quick reference data symbol parameter conditions min typ max unit t phl , t plh propagation delay an to bn; bn to an v cc = 2.5 v; c l =30pf - 2.0 - ns v cc = 3.3 v; c l =50pf - 1.9 - ns c i input capacitance - 4.0 - pf c i/o input/output capacitance - 8.0 - pf c pd power dissipation capacitance per buffer outputs enabled [1] [2] -29-pf outputs disabled [1] [2] -5-pf table 2: ordering information type number package temperature range name description version 74ALVC16245DGG - 40 c to +85 c tssop48 plastic thin shrink small outline package; 48 leads; body width 6.1 mm sot362-1 74alvch16245dgg - 40 c to +85 c 74alvc16245dl - 40 c to +85 c ssop48 plastic shrink small outline package; 48 leads; body width 7.5 mm sot370-1 74alvch16245dl - 40 c to +85 c
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 3 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 5. functional diagram fig 1. logic symbol. fig 2. iec logic symbol. fig 3. bushold circuit. 001aaa853 1b0 1b1 1oe 2oe 1b2 1b3 1b4 1b5 1b6 1b7 1dir 47 46 48 25 44 43 41 40 38 37 2 3 1 5 6 8 9 11 12 24 2b0 2b1 2b2 2b3 2b4 2b5 2b6 2b7 1a0 1a1 1a2 1a3 1a4 1a5 1a6 1a7 2a0 2a1 2a2 2a3 2a4 2a5 2a6 2a7 36 35 33 32 30 29 27 26 13 14 16 17 19 20 22 23 2dir g3 g6 3en1[ba] 6en1[ba] 3en2[ab] 6en2[ab] 2 13 47 36 46 35 3 14 44 33 5 16 43 32 6 17 41 30 8 19 40 29 9 20 38 27 11 22 37 26 12 23 1a0 2a1 2a0 2a2 2a3 2a4 2a5 2a6 2a7 2b1 2b2 2b3 2b4 2b5 2b6 2b7 1oe 1dir 001aaa790 1a1 1a2 1a3 1a4 1a5 1a6 1a7 1b0 2b0 1b1 1b2 1b3 1b4 1b5 1b6 1b7 5 4 2 1 25 24 48 1 2oe 2dir to internal circuit mna004 v cc data input
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 4 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state fig 4. logic diagram. 47 1 1dir 2 48 1b0 1b1 1b2 1b3 1b4 1b5 1b6 1b7 2b0 2b1 2b2 2b3 2b4 2b5 2b6 2b7 46 3 44 5 43 6 41 8 40 9 38 11 37 1a0 1a1 1a2 1a3 1a4 1a5 1a6 1a7 2a0 2a1 2a2 2a3 2a4 2a5 2a6 2a7 12 1oe 2dir 2oe 36 24 13 25 35 14 33 16 32 17 30 19 29 20 27 22 26 23 001aaa789
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 5 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 6. pinning information 6.1 pinning 6.2 pin description fig 5. pin con?guration. 16245 1dir 1oe 1b0 1a0 1b1 1a1 gnd gnd 1b2 1a2 1b3 1a3 v cc v cc 1b4 1a4 1b5 1a5 gnd gnd 1b6 1a6 1b7 1a7 2b0 2a0 2b1 2a1 gnd gnd 2b2 2a2 2b3 2a3 v cc v cc 2b4 2a4 2b5 2a5 gnd gnd 2b6 2a6 2b7 2a7 2dir 2oe 001aaa791 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 table 3: pin description pin symbol description 1 1dir direction control input 2 1b0 data output or input 3 1b1 data output or input 4 gnd ground (0 v) 5 1b2 data output or input 6 1b3 data output or input 7v cc positive supply voltage 8 1b4 data output or input 9 1b5 data output or input 10 gnd ground (0 v) 11 1b6 data output or input
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 6 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 12 1b7 data output or input 13 2b0 data output or input 14 2b1 data output or input 15 gnd ground (0 v) 16 2b2 data output or input 17 2b3 data output or input 18 v cc positive supply voltage 19 2b4 data output or input 20 2b5 data output or input 21 gnd ground (0 v) 22 2b6 data output or input 23 2b7 data output or input 24 2dir direction control input 25 2 oe output enable input (active low) 26 2a7 data input or output 27 2a6 data input or output 28 gnd ground (0 v) 29 2a5 data input or output 30 2a4 data input or output 31 v cc positive supply voltage 32 2a3 data input or output 33 2a2 data input or output 34 gnd ground (0 v) 35 2a1 data input or output 36 2a0 data input or output 37 1a7 data input or output 38 1a6 data input or output 39 gnd ground (0 v) 40 1a5 data input or output 41 1a4 data input or output 42 v cc positive supply voltage 43 1a3 data input or output 44 1a2 data input or output 45 gnd ground (0 v) 46 1a1 data input or output 47 1a0 data input or output 48 1 oe output enable input (active low) table 3: pin description continued pin symbol description
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 7 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 7. functional description 7.1 function table [1] h = high voltage level l = low voltage level x = dont care z = high-impedance off-state. 8. limiting values [1] the input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] above 55 c the value of p tot derates linearly with 11.3 mw/k. [3] above 55 c the value of p tot derates linearly with 8 mw/k. table 4: function table [1] input input or output n oe ndir nan nbn l l a = b input l h input b = a hxz z table 5: limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit v cc supply voltage - 0.5 +4.6 v i ik input diode current v i < 0 v - 50 - ma v i input voltage data inputs with bushold [1] - 0.5 v cc + 0.5 v data inputs without bushold [1] - 0.5 +4.6 v control pins [1] - 0.5 +4.6 v i ok output diode current v o > v cc or v o < 0 v - 50 ma v o output voltage [1] - 0.5 v cc + 0.5 v i o output source or sink current v o = 0 v to v cc - 50 ma i gnd , i cc v cc or gnd current - 100 ma t stg storage temperature - 65 +150 c p tot power dissipation t amb = - 40 c to +85 c ssop package [2] - 850 mw tssop package [3] - 600 mw
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 8 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 9. recommended operating conditions 10. static characteristics table 6: recommended operating conditions symbol parameter conditions min typ max unit v cc supply voltage maximum speed performance c l = 30 pf 2.3 - 2.7 v c l = 50 pf 3.0 - 3.6 v low-voltage applications 1.2 - 3.6 v v i input voltage 0 - v cc v v o output voltage 0 - v cc v t amb operating ambient temperature - 40 - +85 c t r , t f input rise and fall times v cc = 2.3 v to 3.0 v 0 - 20 ns/v v cc = 3.0 v to 3.6 v 0 - 10 ns/v table 7: static characteristics at recommended operating conditions; voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min typ max unit t amb = - 40 c to +85 c [1] v ih high-level input voltage v cc = 2.3 v to 2.7 v 1.7 1.2 - v v cc = 2.7 v to 3.6 v 2.0 1.5 - v v il low-level input voltage v cc = 2.3 v to 2.7 v - 1.2 0.7 v v cc = 2.7 v to 3.6 v - 1.5 0.8 v v oh high-level output voltage v i = v ih or v il i o = - 100 m a; v cc = 2.3 v to 3.6 v v cc - 0.2 v cc -v i o = - 6 ma; v cc = 2.3 v v cc - 0.3 v cc - 0.08 - v i o = - 12 ma; v cc = 2.3 v v cc - 0.6 v cc - 0.26 - v i o = - 12 ma; v cc = 2.7 v v cc - 0.5 v cc - 0.14 - v i o = - 12 ma; v cc = 3.0 v v cc - 0.6 v cc - 0.09 - v i o = - 24 ma; v cc = 3.0 v v cc - 1.0 v cc - 0.28 - v v ol low-level output voltage v i =v ih or v il i o = 100 m a; v cc = 2.3 v to 3.6 v - gnd 0.20 v i o = 6 ma; v cc = 2.3 v - 0.07 0.40 v i o = 12 ma; v cc = 2.3 v - 0.15 0.70 v i o = 12 ma; v cc = 2.7 v - 0.14 0.40 v i o = 24 ma; v cc = 3.0 v - 0.27 0.55 v i li input leakage current v i =v cc or gnd; v cc = 2.3 v to 3.6 v - 0.1 5 m a i oz 3-state output off-state current v i =v ih or v il ; v o =v cc or gnd; v cc = 2.3 v to 3.6 v - 0.1 10 m a
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 9 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state [1] all typical values are measured at t amb =25 c . [2] valid for data inputs of bushold parts. i cc quiescent supply current v cc = 2.3 v to 3.6 v; v i =v cc or gnd; i o = 0 a - 0.2 40 m a d i cc additional quiescent supply current given per data i/o pin with bushold v cc = 2.3 v to 3.6 v; v i =v cc - 0.6 v; i o =0a - 150 750 m a i bhl bushold low sustaining current v cc = 2.3 v; v i = 0.7 v [2] 45 - - m a v cc = 3.0 v; v i = 0.8 v [2] 75 150 - m a i bhh bushold high sustaining current v cc = 2.3 v; v i = 1.7 v [2] - 45 - - m a v cc = 3.0 v; v i = 2.0 v [2] - 75 - 175 - m a i bhlo bushold low overdrive current v cc = 3.6 v [2] 500 - - m a i bhho bushold high overdrive current v cc = 3.6 v [2] - 500 - - m a c i input capacitance - 4.0 - pf c i/o input/output capacitance - 8.0 - pf table 7: static characteristics continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min typ max unit
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 10 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 11. dynamic characteristics [1] all typical values are measured at t amb =25 c . [2] typical values are measured at v cc = 2.5 v. [3] typical values are measured at v cc = 3.3 v. [4] c pd is used to determine the dynamic power dissipation (p d in m w). p d = c pd v cc 2 f i n+ ? (c l v cc 2 f o ) where: f i = input frequency in mhz; f o = output frequency in mhz; c l = output load capacitance in pf; v cc = supply voltage in volts; n = total load switching outputs; ? (c l v cc 2 f o ) = sum of outputs. [5] the condition is v i = gnd to v cc . table 8: dynamic characteristics at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); test circuit figure 8 . symbol parameter conditions min typ max unit t amb = - 40 c to +85 c [1] t phl , t plh propagation delay nan to nbn; nbn to nan see figure 6 v cc = 2.3 v to 2.7 v [2] 1.0 2.0 3.7 ns v cc = 3.0 v to 3.6 v [3] 1.0 1.9 3.0 ns v cc = 2.7 v 1.0 2.1 3.6 ns t pzh , t pzl 3-state output enable time n oe to nan; n oe to nbn see figure 7 v cc = 2.3 v to 2.7 v [2] 1.0 2.7 5.7 ns v cc = 3.0 v to 3.6 v [3] 1.0 2.3 4.4 ns v cc = 2.7 v 1.0 3.0 5.4 ns t phz , t plz 3-state output disable time n oe to nan; n oe to nbn see figure 7 v cc = 2.3 v to 2.7 v [2] 1.0 2.2 5.2 ns v cc = 3.0 v to 3.6 v [3] 1.0 2.8 4.1 ns v cc = 2.7 v 1.0 3.1 4.6 ns c pd power dissipation capacitance per buffer outputs enabled [4] [5] -29-pf outputs disabled [4] [5] -5-pf
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 11 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 12. waveforms measurement points are given in t ab le 9 . v ol and v oh are typical output voltage drop that occur with the output load. fig 6. input (nan, nbn) to output (nbn, nan) propagation delay times. table 9: measurement points supply voltage input output v cc v m v m < 2.7 v 0.5 v cc 0.5 v cc 3 2.7 v 1.5 v 1.5 v measurement points are given in t ab le 10 . v ol and v oh are typical output voltage drop that occur with the output load. fig 7. 3-state enable and disable times. table 10: measurement points supply voltage input output v cc v m v m v x v y < 2.7 v 0.5 v cc 0.5 v cc v ol + 0.15 v v oh - 0.15 v 3 2.7 v 1.5 v 1.5 v v ol + 0.3 v v oh - 0.3 v 001aaa792 nan, nbn input nbn, nan output t phl t plh gnd v i v m v m v oh v ol 001aaa793 t plz t phz outputs disabled outputs enabled v y v x outputs enabled qn output low-to-off off-to-low qn output high-to-off off-to-high noe input v i v ol v oh v cc v m v m gnd gnd t pzl t pzh v m v m
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 12 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state test data is given in t ab le 11 . de?nitions test circuit: r l = load resistor. c l = load capacitance includes jig and probe capacitance. r t = termination resistance should be equal to z o of pulse generator. fig 8. load circuitry for switching times. table 11: test data supply voltage input load v ext v cc v i t r , t f c l r l t plh , t phl t phz , t pzh t plz , t pzl < 2.7 v v cc 2.0 ns 30 pf 500 w open gnd 2 v cc 2.7 v - 3.6 v 2.7 v 2.5 ns 50 pf 500 w open gnd 2 v cc v ext v cc v i v o mna616 d.u.t. c l r t r l r l pulse generator
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 13 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 13. package outline fig 9. package outline ssop48. unit a 1 a 2 a 3 b p cd (1) e (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm 0.4 0.2 2.35 2.20 0.25 0.3 0.2 0.22 0.13 16.00 15.75 7.6 7.4 0.635 1.4 0.25 10.4 10.1 1.0 0.6 1.2 1.0 0.85 0.40 8 0 o o 0.18 0.1 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. sot370-1 99-12-27 03-02-19 (1) w m b p d h e e z e c v m a x a y 48 25 mo-118 24 1 q a a 1 a 2 l p q detail x l (a ) 3 pin 1 index 0 5 10 mm scale ssop48: plastic shrink small outline package; 48 leads; body width 7.5 mm sot370-1 a max. 2.8
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 14 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state fig 10. package outline tssop48. unit a 1 a 2 a 3 b p cd (1) e (2) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.2 0.1 8 0 o o 0.1 dimensions (mm are the original dimensions). notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. sot362-1 99-12-27 03-02-19 w m q a a 1 a 2 d l p q detail x e z e c l x (a ) 3 0.25 124 48 25 y pin 1 index b h 1.05 0.85 0.28 0.17 0.2 0.1 12.6 12.4 6.2 6.0 0.5 1 0.25 8.3 7.9 0.50 0.35 0.8 0.4 0.08 0.8 0.4 p e v m a a tssop48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm sot362-1 a max. 1.2 0 2.5 5 mm scale mo-153
9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 15 of 17 philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 14. revision history table 12: revision history document id release date data sheet status change notice order number supersedes 74alvc_alvch16245_3 20040512 product data - 9397 750 13117 74alvch16245_2 74alvc16245_ 74alvch16245_1 modi?cations: ? the format of this data sheet has been redesigned to comply with the current presentation and information standard of philips semiconductors. ? section 1 gener al descr iption updated. 74alvc16245_ 74alvch16245_1 19980325 product speci?cation - 9397 750 03385 - 74alvch16245_2 19980629 product speci?cation - 9397 750 04538 74alvch16245_1 74alvch16245_1 19950102 preliminary speci?cation -- -
philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 9397 750 13117 ? koninklijke philips electronics n.v. 2004. all rights reserved. product data sheet rev. 03 12 may 2004 16 of 17 15. data sheet status [1] please consult the most recently issued data sheet before initiating or completing a design. [2] the product status of the device(s) described in this data sheet may have changed since this data sheet was published. the l atest information is available on the internet at url http://www.semiconductors.philips.com. [3] for data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 16. de?nitions short-form speci?cation the data in a short-form speci?cation is extracted from a full data sheet with the same type number and title. for detailed information see the relevant data sheet or data handbook. limiting values de?nition limiting values given are in accordance with the absolute maximum rating system (iec 60134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the speci?cation is not implied. exposure to limiting values for extended periods may affect device reliability. application information applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors make no representation or warranty that such applications will be suitable for the speci?ed use without further testing or modi?cation. 17. disclaimers life support these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips semiconductors for any damages resulting from such application. right to make changes philips semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. when the product is in full production (status production), relevant changes will be communicated via a customer product/process change noti?cation (cpcn). philips semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise speci?ed. 18. contact information for additional information, please visit: http://www.semiconductors.philips.com for sales of?ce addresses, send an email to: sales.addresses@www.semiconductors.philips.com level data sheet status [1] product status [2] [3] de?nition i objective data development this data sheet contains data from the objective speci?cation for product development. philips semiconductors reserves the right to change the speci?cation in any manner without notice. ii preliminary data quali?cation this data sheet contains data from the preliminary speci?cation. supplementary data will be published at a later date. philips semiconductors reserves the right to change the speci?cation without notice, in order to improve the design and supply the best possible product. iii product data production this data sheet contains data from the product speci?cation. philips semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. relevant changes will be communicated via a customer product/process change noti?cation (cpcn).
? koninklijke philips electronics n.v. 2004 all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. date of release: 12 may 2004 document order number: 9397 750 13117 published in the netherlands philips semiconductors 74alvc16245; 74alvch16245 16-bit bus transceiver with direction pin; 3-state 19. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 quick reference data . . . . . . . . . . . . . . . . . . . . . 2 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 6 pinning information . . . . . . . . . . . . . . . . . . . . . . 5 6.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 6.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 7 functional description . . . . . . . . . . . . . . . . . . . 7 7.1 function table . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 7 9 recommended operating conditions. . . . . . . . 8 10 static characteristics. . . . . . . . . . . . . . . . . . . . . 8 11 dynamic characteristics . . . . . . . . . . . . . . . . . 10 12 waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 13 package outline . . . . . . . . . . . . . . . . . . . . . . . . 13 14 revision history . . . . . . . . . . . . . . . . . . . . . . . . 15 15 data sheet status . . . . . . . . . . . . . . . . . . . . . . . 16 16 de?nitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 17 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 18 contact information . . . . . . . . . . . . . . . . . . . . 16

▲Up To Search▲

Price & Availability of 74ALVC16245DGG

	To Download 74ALVC16245DGG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .